Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (10)
2026 · Paper 1 · Q1(i) · p.2
Explain the difference between a Ø10 mm hole and an M10 mm hole.
Marking scheme
Difference Ø10 mm hole Award 3 Marks M10 mm hole Award 3 Marks Total (6) Marks
2026 · Paper 1 · Q7(b)(iv) · p.8
A pneumatic fitting is to be manufactured to the dimensions and tolerances shown. State the: Tolerance of the hole. [Image: Diagram showing a pneumatic fitting with dimensions for body and hole. Body: Ø20.00 ± 0.5 mm. Hole: Ø14.00 ± 0.1 mm.]
2026 · Paper 1 · Q7(b)(iii) · p.8
A pneumatic fitting is to be manufactured to the dimensions and tolerances shown. State the: Smallest diameter of the body; [Image: Diagram showing a pneumatic fitting with dimensions for body and hole. Body: Ø20.00 ± 0.5 mm. Hole: Ø14.00 ± 0.1 mm.]
2026 · Paper 1 · Q7(b)(ii) · p.8
A pneumatic fitting is to be manufactured to the dimensions and tolerances shown. State the: Largest diameter of the hole; [Image: Diagram showing a pneumatic fitting with dimensions for body and hole. Body: Ø20.00 ± 0.5 mm. Hole: Ø14.00 ± 0.1 mm.]
2026 · Paper 1 · Q7(b)(i) · p.8
A pneumatic fitting is to be manufactured to the dimensions and tolerances shown. State the: Nominal diameter of the body; [Image: Diagram showing a pneumatic fitting with dimensions for body and hole. Body: Ø20.00 ± 0.5 mm. Hole: Ø14.00 ± 0.1 mm.]
2023 · Paper 1 · Q7(b)(iv) · p.8
A copper fitting and a steel shaft are machined to the dimensions shown below. State the: Tolerance of the hole in the copper fitting. [Diagram: A copper fitting with a hole of Ø16.0 ± 0.03 mm and a steel shaft of Ø16.0 ± 0.05 mm.]
2023 · Paper 1 · Q7(b)(iii) · p.8
A copper fitting and a steel shaft are machined to the dimensions shown below. State the: Smallest diameter of the shaft. [Diagram: A copper fitting with a hole of Ø16.0 ± 0.03 mm and a steel shaft of Ø16.0 ± 0.05 mm.]
2023 · Paper 1 · Q7(b)(ii) · p.8
A copper fitting and a steel shaft are machined to the dimensions shown below. State the: Nominal diameter of the shaft. [Diagram: A copper fitting with a hole of Ø16.0 ± 0.03 mm and a steel shaft of Ø16.0 ± 0.05 mm.]
2023 · Paper 1 · Q7(b)(i) · p.8
A copper fitting and a steel shaft are machined to the dimensions shown below. State the: Largest diameter of the hole in the copper fitting. [Diagram: A copper fitting with a hole of Ø16.0 ± 0.03 mm and a steel shaft of Ø16.0 ± 0.05 mm.]
2018 · Paper 1 · Q7(b) · p.8
A hole and shaft are manufactured to the dimensions shown. State the: (i) Nominal diameter of the shaft; (ii) Largest diameter of the shaft; (iii) Smallest diameter of the hole; (iv) The type of fit which will result from the assembly of the largest shaft and the smallest hole. [Diagram: A shaft with dimensions 20.0 ± 0.08 mm and a hole with dimensions 20.0 ± 0.05 mm.]
Marking scheme
(i) Nominal diameter of the shaft: 20.00 mm (5 marks) (ii) Largest diameter of the shaft: 20.08 mm (5 marks) (iii) Smallest diameter of the hole: 19.95 mm (5 marks) (iv) Type of fit. Interference fit (5 marks) Total (20 marks)