Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (12)
2024 · Paper 1 · Q7(a) · p.8
Name any two types of fit in a hole and shaft assembly. (ii) Describe any one of the fits named at Q7 (a)(i) above.
Marking scheme
(i) Types of fit (Award 2 @ 3 Marks) (ii) Description (Award 1 @ 6 Marks) Total (12) Marks
2021 · Paper 1 · Q7(b)(iv) · p.8
A hole and shaft assembly is manufactured to the dimensions shown. State the: The type of fit which will result from the assembly of the largest shaft and the smallest hole. [Diagram: A hole with diameter Ø30 ± 0.06 mm and a shaft with diameter Ø30 ± 0.08 mm.]
2021 · Paper 1 · Q7(a)(ii) · p.8
Describe any one of the fits named at Q7(a)(i).
Marking scheme
(i) A Clearance fit, Interference fit or Transition fit (ii) Clearance fit - The shaft is always smaller than the hole. Interference fit - The shaft is always larger than the hole. Or Transition fit - The shaft can be larger or smaller than the hole. [(i) Name Award 2 @ 4 Marks] [(ii) Describe Award 1 @ 4 Marks] [Total (12) Marks]
2021 · Paper 1 · Q7(a)(i) · p.8
Name two types of fit possible when assembling a shaft and a hole.
2019 · Paper 1 · Q7(b)(iv) · p.8
A hole and shaft assembly is manufactured to the dimensions shown. State the: The tolerance of the hole. [Diagram: A hole with diameter Ø32 ± 0.06mm and a shaft with diameter Ø32 ± 0.08mm.]
2019 · Paper 1 · Q7(b)(iii) · p.8
A hole and shaft assembly is manufactured to the dimensions shown. State the: Smallest diameter of the hole; [Diagram: A hole with diameter Ø32 ± 0.06mm and a shaft with diameter Ø32 ± 0.08mm.]
2019 · Paper 1 · Q7(b)(ii) · p.8
A hole and shaft assembly is manufactured to the dimensions shown. State the: Largest diameter of the shaft; [Diagram: A hole with diameter Ø32 ± 0.06mm and a shaft with diameter Ø32 ± 0.08mm.]
2019 · Paper 1 · Q7(b)(i) · p.8
A hole and shaft assembly is manufactured to the dimensions shown. State the: Nominal diameter of the shaft; [Diagram: A hole with diameter Ø32 ± 0.06mm and a shaft with diameter Ø32 ± 0.08mm.]
2019 · Paper 1 · Q7(a)(iii) · p.8
Describe any two of the following: Upper limit.
2019 · Paper 1 · Q7(a)(ii) · p.8
Describe any two of the following: Clearance fit,
Marking scheme
OR (i) & (ii) Any three electronic components: A. DC Motor - Used to provide mechanical movement. [2+3 marks] B. A buzzer - Used to provide an audible warning etc. [2+3 marks] C. A switch - Used to turn on / off the control circuit. [2+3 marks] D. Light Emitting Diode (LED) – Used as an indicator to show the circuit is on. [2+3 marks]
2019 · Paper 1 · Q7(a)(i) · p.8
Describe any two of the following: Interference fit,
2017 · Paper 1 · Q1(e) · p.2
Explain the term clearance fit in relation to a shaft and a hole.
Marking scheme
A clearance fit is achieved when the largest shaft fits into the smallest hole. [5 Marks]