Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (12)
2017 · Paper 1 · Q5(c)(ii) · p.8
Describe, with the aid of a suitable diagram(s), any one of the following: The essential differences between Metal Inert Gas (MIG) welding and Tungsten Inert Gas (TIG) welding.
Marking scheme
MIG welding: A semi-automatic process. A consumable bare wire electrode is fed continuously into the weld pool area through the welding torch. An inert gas, such as Argon, creates a protective shield around the weld pool giving a fluxing action. The feed rate and flow rate of the gas are set by the operator. This allows the operator to guide the torch along the weld once the arc is generated between the electrode and the work. MIG welding does not produce a slag on the weld. [Diagram: MIG welding setup showing a welding torch with wire feed and gas nozzle, connected to a power source and gas cylinder.] Tungsten inert gas welding, TIG, TAGS. An arc is formed between the non-consumable electrode and the metal being welded. The inert gas shielded arc is used to flux the joint, argon is often used to prevent oxygen getting to the joint area. A stainless steel filler metal is added manually to the weld pool when necessary. A high frequency generator provides a path for the welding current. [Diagram: TIG welding setup showing a TIG torch with a non-consumable electrode, gas nozzle, connected to a power source and gas cylinder. A separate filler rod is shown being fed into the weld pool.]
2017 · Paper 1 · Q5(c)(i) · p.8
Describe, with the aid of a suitable diagram(s), any one of the following: The transformer-rectifier circuit used in manual metal arc welding.
Marking scheme
The transformer-rectifier circuit used in manual metal arc welding. [Diagram: A circuit diagram showing a transformer (labeled A), a rectifier bridge (labeled B), and a capacitor (labeled C) connected to an output.] A - Transformer: A step-down transformer is used to change the mains voltage from 220V to a suitable level (80-100V) for welding. This will provide the high current needed for welding. This type of transformer has more turns on the primary coil than the secondary coil and will induce alternating current (AC) at a lower voltage. B - Rectifier: The rectifier changes alternating current (AC) to direct current (DC). It consists of four diodes which allows two of the diodes to conduct on each half-cycle of the AC supply. C - Capacitor: The capacitor is employed to provide a smooth supply of low voltage DC.
2017 · Paper 1 · Q5(b)(v) · p.8
Answer any three of the following: Give two benefits of using resistance seam welding in the production of house radiators.
Marking scheme
Benefits of seam welding domestic radiators: • Creates a sealed unit • High speed welding • Easily automated • Suitable for high rate production • Economical.
2017 · Paper 1 · Q5(b)(iv) · p.8
Answer any three of the following: Outline three safety features integrated into oxy-acetylene welding equipment.
Marking scheme
Safety features integrated into oxy-acetylene welding equipment: • The colour coding on the cylinders and the hoses helps prevent any possible mix-up of the gases and connections. • The oxygen cylinder is usually thinner and taller than the acetylene cylinder. • The connections for the different gases have either left or right-hand thread forms. • The flashback arrestors prevent the flame returning to the cylinders. • Cylinders can be turned off when finished operating the equipment.
2017 · Paper 1 · Q5(b)(iii) · p.8
Answer any three of the following: Describe two hazards which may be encountered in underwater welding.
Marking scheme
Hazards of welding underwater: • Underwater welding adds the danger of being shocked, or producing a mixture of oxygen and hydrogen together in bubbles in the arc, which can lead to an explosion. • If a diver surfaces too fast, he is always in danger of getting the bends (severe pain in joints that is caused by not properly depressurizing). • Sharks and large ocean predators are always a potential threat when welding underwater, as well as the diving suit becoming damaged or the oxygen tanks becoming loose or emptied. • The ocean current can actually carry a welder off, which can result in disastrous consequences. • Nitrogen can build up in the diver's blood and create deposits. • Of course, there is the most common death involved with water - drowning.
2017 · Paper 1 · Q5(b)(ii) · p.8
Answer any three of the following: Outline the reasons for porosity in welding.
Marking scheme
Porosity in welding: • The presence of moisture in the weld • Cylinder out of gas • Presence of paint, oil or grease • Weld nozzle is not close enough to weld • Shielding gas has been blown away due to drafts.
2017 · Paper 1 · Q5(b)(i) · p.8
Answer any three of the following: Describe the term dissolved acetylene.
Marking scheme
If acetylene is compressed into a cylinder, it would explode under high pressure. Acetylene cylinders are packed with a porous material that is filled with acetone, this can absorb 25 times its own volume of acetylene. Dissolved acetylene is the name given to this form of acetylene fuel.
2017 · Paper 1 · Q5(a)(ii) · p.8
Describe, with the aid of diagram(s), the main principles of operation for the selected welding process. [Image: A large diameter steel pipe being welded.]
Marking scheme
In submerged arc welding, a bare wire electrode is used. It is fed automatically from a spool and generates an electric arc to heat the metal. The flux, in powder form, is fed from a hopper to completely cover the joint and the tip of the electrode. The arc creates the heat to melt the joint, flux and electrode. A slag is formed to provide a protective coating for the weld. The excess flux powder can be collected and used again. Submerged arc welding is a fully automated process. Applications: used for large scale straight line welds such as steel reinforcing beams, shipbuilding and bridge construction. [Diagram: Submerged Arc Welding setup showing a DC power source, electrode wire feeding from a spool, a hopper feeding flux powder, and the weld pool with the electrode tip submerged in flux.]
2017 · Paper 1 · Q5(a)(i) · p.8
The heavy steel pipe shown is first rolled into shape and is to be completed by welding. Select a suitable automated welding process for joining the seams along the length of the heavy steel pipe. Justify your selection. [Image: A large diameter steel pipe being welded.]
Marking scheme
Submerged arc welding (SAW) is a suitable welding technique for the steel pipe as SAW is an automated process used for long uninterrupted welding.
2016 · Paper 1 · Q5(a) · p.8
The drum set shown is fabricated from sheet stainless steel which is rolled and welded. The resultant weld on the drum shell is smoothly finished. [Image: Drum set]. (i) Select a suitable welding process used in the manufacture of the stainless steel drum and outline one reason for your selection. (ii) Describe, with the aid of a diagram(s), the key principles of the welding process selected.
2015 · Paper 1 · Q5(b) · p.8
The kart shown has a welded mild steel frame. [Image: A go-kart with a welded steel frame.]
2015 · Paper 1 · Q5(a) · p.8
Answer any three of the following: (i) Outline two methods used to prevent porosity occurring in welds. (ii) Compare the electrode used in MIG welding and the electrode used in TIG welding. (iii) Describe the carburising flame used in oxy-acetylene welding. (iv) Suggest a suitable method to protect against each of the following when welding: • Electric shock • Intense light from welding • Welding fumes.