Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (8)
2024 · Paper 1 · Q1(j) · p.3
Compare the indenters used in both the Brinell and the Vickers hardness tests.
Marking scheme
The Brinell hardness test uses a hardened steel ball as an indenter. The Vickers hardness test uses a diamond, square-based pyramid indenter. It has a point angle of 136°. [Diagram showing two indentation tests: one with a ball indenter under load, showing the ball, load, and indentation; the other with a diamond indenter under load, showing the diamond indenter, load, and indentation.] (5)
2024 · Paper 1 · Q3(c)(ii) · p.5
Describe, with the aid of a diagram(s), one suitable non-destructive test that may be used to examine the aluminium linkage arm for internal flaws.
Marking scheme
Reasons for non-destructive testing (NDT) of the linkage arm: • Product will not be destroyed, cost saving. • Safety and quality control. • Speed - immediate results can be generated. • Accuracy - excellent at detecting large and small imperfections. (4+4)
2024 · Paper 1 · Q3(c)(i) · p.5
Outline two reasons why non-destructive tests are used during the production of the linkage arm.
Marking scheme
Cup and cone fracture is a type of failure observed in ductile metals and plastics due to tensile stress. This type of fracture gets its name from the resulting shapes at the end of the broken pieces after a failure has occurred. [Diagram showing a cup and cone fracture.] (2+2)
2024 · Paper 1 · Q3(b)(iii) · p.5
Describe, with the aid of a diagram(s), the following terms related to tensile testing: • necking • cup and cone fracture.
Marking scheme
Necking is a type of plastic deformation observed in ductile materials subjected to tensile stress. This is where the middle of the specimen is noticeably thinner than the rest of the specimen and with a little more stress the piece is going to fracture. [Diagram showing a tensile test specimen before necking and during necking, with arrows indicating load.]
2024 · Paper 1 · Q3(b)(i) · p.5
Using the graph paper supplied, plot the stress-strain diagram for the alloy.
Marking scheme
[Graph: Stress (N/mm²) on the y-axis from 0 to 400, Strain (x 1000) on the x-axis from 0 to 8. The graph shows a curve starting at the origin, increasing linearly to approximately (1.5, 135), then increasing non-linearly to a peak of around 320 at a strain of about 6.0, and then leveling off.] (10)
2024 · Paper 1 · Q3(b) · p.5
The results shown were obtained from a tensile test on an aluminum alloy specimen. [Table: Stress (N/mm²) vs Strain (x1000) with 9 data points.]
2024 · Paper 1 · Q3(a)(iii) · p.5
Describe, with the aid of diagram(s), a testing procedure used to determine the toughness of a material.
Marking scheme
This will determine the toughness of the material which indicates the ability to withstand impact or shock loads. Test pieces are notched and held in the vice associated with the machine. A pendulum hammer strikes the test piece and determines the energy absorbed in breaking the piece. This gives a numerical value for the toughness of the material. Izod Test • 167 joules striking energy. • Test specimen is vertical. • Test piece is clamped at one end. • Test piece notch is facing the pendulum. • The distance the pendulum travels after breaking the piece will give the toughness value. Charpy Test • 300 joules striking energy. • Test specimen is Horizontal. • Test piece is clamped at both ends. • Test piece notch is facing away from the pendulum. • The distance the pendulum travels after breaking the piece will give the toughness value. [Diagram of Izod and Charpy impact testing machines, showing the pendulum, specimen, anvil, and dial.] (8)
2024 · Paper 1 · Q6(b)(iv) · p.8
Identify a suitable Non-Destructive Test (NDT) for the inspection of porosity in welds.
Marking scheme
Radiography (X-ray) NDT can be used to check welds for porosity. The X-Ray test provides a highly sensitive image of the internal structure of the material indicating if porosity is present in the weld. [Image showing a weld with porosity indicated.]