Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (8)
2025 · Paper 1 · Q3(a)(iii) · p.5
Describe, with the aid of a diagram(s), the principles of tensile testing. [Image: a jet engine with a focus on the compressor blades.]
Marking scheme
A standardised test specimen is placed in an extensometer machine where a measured tensile Load/Stress is applied. The resultant extension is plotted on a Load/Extension or Stress/Strain diagram where the tensile strength of the material can be assessed. Typical graphs represent tensile tests for a variety of materials are shown. • Very hard and brittle (red), high stress with only a limited degree of elasticity before failure. Results in a brittle fracture. • Tough material (green), elastic and plastic deformation, necking and failure. Results in a ductile fracture. • Very Ductile material (blue), a lot of plastic deformation under load before failure. [Diagram: A tensile testing machine with a specimen held by clamps, labelled 'Clamp' and 'Sample'. Below this, a graph labelled 'Load / Stress' on the y-axis and 'Extension / Strain' on the x-axis, showing three curves: red (Hard material), green (Tough material), and blue (Ductile material).]
2023 · Paper 1 · Q3(b)(iii) · p.5
Calculate the 0.1% proof stress. [Visual aid: Table: Load (kN) vs Extension (mm) data from a tensile test.]
Marking scheme
From the graph: 84 kN 0.1% proof stress = 84 / C.S.A = 0.42 kN/mm² 4
2023 · Paper 1 · Q3(b)(ii) · p.5
Determine the ultimate tensile strength (UTS) for the specimen. [Visual aid: Table: Load (kN) vs Extension (mm) data from a tensile test.]
Marking scheme
U.T.S. = Max. Load / C.S.A. = 135 / (π. (8²)) = 0.67 kN/mm² 4
2023 · Paper 1 · Q3(b)(i) · p.5
Using the graph paper supplied, plot the load-extension diagram.
Marking scheme
[Graph: Load-extension graph showing load (kN) on the y-axis and extension (mm) on the x-axis. The curve starts at (0,0), rises to a peak load of approximately 135 kN at an extension of around 4 mm, then decreases slightly. Key points marked: Yield point around 84 kN at extension 0.08 mm. The graph shows elastic and plastic deformation regions.] 10
2021 · Paper 1 · Q3(b) · p.5
The results shown were obtained from a tensile test on an aluminium alloy specimen. [Table: Stress (N/mm²) vs Strain (x1000) with values: (50, 0.60), (125, 1.40), (195, 2.20), (260, 3.00), (300, 3.70), (330, 5.00), (350, 7.00), (352, 8.50)]
2020 · Paper 1 · Q2(b) · p.5
The results shown below were obtained from a tensile test on a non-ferrous alloy with a 10 mm diameter and 50 mm gauge length. [Table: Load (kN) vs Extension (mm) with data points: Load (kN) 15, 25, 40, 60, 80, 100, 107, 108, 105, 96; Extension (mm) 0.06, 0.10, 0.16, 0.26, 0.38, 0.65, 0.90, 1.0, 1.2, 1.4.]
2018 · Paper 1 · Q2(a)(ii) · p.5
Describe, with the aid of a diagram(s), the principles of tensile testing.
Marking scheme
Tensile testing: Extensometer tensile testing machine is used. Specimen (rectangular or circular cross section) is clamped at both ends. Machine is turned on and begins to apply a tensile force on the specimen. The specimen will continue to stretch until it fractures. A graph readout will be produced from the tensile test. Further calculations can be determined from the graph produced. [Diagram: Shows an extensometer tensile testing machine with a specimen clamped at both ends. Labels indicate 'Extensometer'. Below this are diagrams of 'Tensile test specimens' showing 'rectangular' and 'circular' shapes. Further diagrams show 'Ductile fracture' (cup and cone) and 'Brittle fracture'.]
2015 · Paper 1 · Q2(b)(ii) · p.5
Analyse the effects of the tensile test on the shape of the test specimen shown at both B and C. [Visual aid: Image: Three test specimens, one before testing, one elongated and necked, one fractured.]