Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (12)
2024 · Paper 1 · Q5(c)(iii) · p.7
Explain why FCC crystalline structures are most associated with ductility in metals.
Marking scheme
FCC crystalline structure and ductility: In the FCC structure atoms are at the corners of a cube and a single atom in the centre of each face of the cube. These atoms are more tightly packed than BCC structures, which allows slip to happen more easily and results in a more ductile metal. [Diagram showing FCC structure with atoms at corners and face centres.] (Any two @ 8 + 8)
2024 · Paper 1 · Q5(b)(iii) · p.7
State the melting point of metal A and the melting point of metal B.
Marking scheme
A - 270°C B - 630°C (2+2)
2024 · Paper 1 · Q5(b)(ii) · p.7
Sketch the cooling curve for the alloy with 30% metal B, referring to the solidification temperatures in the table above.
Marking scheme
[Cooling curve: Temperature (°C) on the y-axis, Time on the x-axis. The curve shows a decrease in temperature, a plateau at 445°C (Start of solidification), a further decrease, and another plateau at 300°C (End of solidification), followed by a final decrease.]
2024 · Paper 1 · Q5(b)(i) · p.7
Draw the equilibrium diagram according to the given data and label the liquidus and solidus lines.
Marking scheme
[Phase diagram: Temperature (°C) on the y-axis from 0 to 700, % Metal B on the x-axis from 0 to 100. The diagram shows a liquidus line and a solidus line, forming a two-phase region between them.] (10)
2024 · Paper 1 · Q5(b) · p.7
The table shows the solidification temperatures for various alloys of metal A and metal B. [Table: % of metal B in alloy vs Start and End of solidification (°C) for 11 alloys.]
2022 · Paper 1 · Q4(a)(i) · p.6
Explain one difference between cast iron and steel. [Image: photograph of the Ha'penny Bridge in Dublin.]
2017 · Paper 1 · Q1(j) · p.3
The rotor blades of a helicopter are subjected to high speeds and varying weather conditions, which could lead to fatigue failure. Explain the term fatigue failure.
Marking scheme
Metal fatigue is failure due to on/off loading or cyclic stressing. Fatigue failure begins as a minute crack which grows under the action of fluctuating stress. 5
2017 · Paper 1 · Q1(h) · p.3
Most golf clubs are manufactured with either steel or carbon-fibre (graphite) shafts. Describe two benefits of using carbon-fibre (graphite) shafts over steel shafts. [Visual aid: Diagram: a golf club shaft labelled 'shaft'.]
Marking scheme
Graphite is much lighter than steel. A light club can be swung faster than a heavy one means more distance. A graphite shaft will not rust compared to a steel shaft and will have more flexibility in it. Graphite tends to have a softer, more dampened feel. (Any two) 3 + 2
2017 · Paper 1 · Q1(e) · p.3
Give two reasons why stainless steel is suitable for the manufacture of surgical devices.
Marking scheme
Hard material capable of retaining a sharp edge, non-toxic, tough, does not contaminate, etc. (Any two) 3 + 2
2017 · Paper 1 · Q3(a)(ii) · p.6
Distinguish between the composition of cast iron and the composition of low carbon steel. [Visual aid: Image: A cast iron pizza oven.]
Marking scheme
Most cast irons have a chemical composition of 2.5 – 4.0% carbon with varying amounts of silicon, manganese, sulphur, etc. Most cast irons are brittle, have a relatively low melting point, resist wear with excellent casting properties. Low carbon steels contain up to 0.3% carbon with a range of properties including good machinability, welds easily, malleable, ductile, etc.
2017 · Paper 1 · Q3(a)(i) · p.6
Pizza ovens can be constructed from a variety of materials such as brick, clay, steel and cast iron. The pizza oven shown is manufactured from cast iron. Explain two reasons why cast iron is used in the manufacture of this pizza oven. [Image: A cast iron pizza oven.]
Marking scheme
Use of Cast iron for stoves • The cast iron is much denser and heavier than steel and therefore it takes more time for the fire to heat the metal before the heat can then be radiated out. • Cast iron holds the heat for longer than steel and takes longer to cool once the fire has been extinguished. • Cast iron stoves are generally more expensive than steel stoves.
2017 · Paper 1 · Q4(c)(i) · p.7
Select any two from (i), (ii) or (iii) below and differentiate between the terms in each: Amorphous solid structures and crystalline solid structures;
Marking scheme
Crystalline solid structures [Diagram: A regular, repeating arrangement of circles representing atoms.] Amorphous solid structures [Diagram: A random, disordered arrangement of circles representing atoms.] Crystalline atoms are arranged in a pattern. Amorphous atoms are arranged randomly.