Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (12)
2022 · Paper 1 · Q7(a)(ii) · p.9
Give two properties of expanded polystyrene (ESP) which make it suitable for use in the helmet liner.
2020 · Paper 1 · Q2(a)(ii) · p.5
Material strength may be partly described in terms of the following properties: • Compressive strength • Tensile strength • Shear strength. Describe each of these properties. [Image: A green Kawasaki jet ski with the word 'hull' pointing to the lower body.]
Marking scheme
Compressive strength: Axial forces that push or press on an object. Tensile strength: Two forces pull or stretch an object in opposite directions. Shear strength: Shear is two forces acting parallel to each other but in opposite directions creating a cutting action. [Diagrams: Arrows indicating compressive, tensile, and shear forces acting on blocks.]
2019 · Paper 1 · Q1(f) · p.3
Outline two advantages for using nylon to make the wheel shown.
Marking scheme
Will turn well into shape, wear resistant, range of colours, will not crush under pressure, etc. (3+2 marks)
2019 · Paper 1 · Q2(a)(i) · p.5
Describe the terms metal fatigue and metal hardness.
Marking scheme
Metal fatigue is failure due to on/off loading or cyclic stressing. Fatigue failure begins as a minute crack which grows under the action of fluctuating stress. Hardness is the property of the material which enables it to resist plastic deformation, usually by penetration or by indentation. Hardness is also referred to as temper or the resistance to bending, scratching or abrasion. (3+3 marks)
2019 · Paper 1 · Q2(a) · p.5
The design and manufacture of the engine crankshaft in high performance sports cars must take into account both metal fatigue and metal hardness. [Image: a detailed photograph of a car engine crankshaft.]
2018 · Paper 1 · Q1(i) · p.3
Lead is used in roof flashings but is subject to metal creep. Explain the term metal creep.
Marking scheme
Charles Parsons. Irish engineer (1854 –1931) who is credited as the inventor of the steam turbine. He worked as an engineer on dynamo and turbine design and power generation, with great influence on the naval and electrical engineering fields. He also developed optical equipment for searchlights and telescopes.
2018 · Paper 1 · Q2(b)(ii) · p.5
Compare graph A and graph C with reference to each of the following: the shape of the graph, material properties.
Marking scheme
Graph A has a relatively short elastic phase where it will return to its original shape and length with the removal of the strain. The metal has very ductile properties where it extends with a relatively small addition of force before fracture. It will stretch for a long time before necking and breaking. Metal A has low tensile strength yet is ductile. Graph C has an extended elastic range where the metal stays strong and will return to its original shape. The shape of graph C shows clearly defined upper and lower yield points. This is followed by a ductile stage until the metal reaches ultimate tensile strength in advance of necking and fracture. Metal C is strong, good in tension and is less ductile than metal A.
2018 · Paper 1 · Q2(b)(i) · p.5
State which one of the three metals – copper, low carbon steel or stainless steel is most suitable for each of the graphs A, B and C.
Marking scheme
A - copper, B - stainless steel, C - low carbon steel
2018 · Paper 1 · Q2(b) · p.5
The graphs A, B and C shown below were produced following tensile tests on three metals - copper, low carbon steel and stainless steel. [Graph: Stress (N/mm²) vs Strain (%) for three metals labelled A, B, and C. Curve C reaches the highest stress, followed by B, then A. All curves show initial elastic deformation, yielding, and then plastic deformation.]
2018 · Paper 1 · Q4(c) · p.7
Select any two from (i), (ii) or (iii) below and explain the difference between each term: (i) Partial solubility alloy and solid solution alloy; (ii) Work hardening and age hardening; (iii) Ductility in BCC structures and ductility in FCC structures.
2014 · Paper 1 · Q1(j) · p.3
Describe two important properties of a material which is suitable for the manufacture of a prosthetic hand.
2014 · Paper 1 · Q2(a)(i) · p.5
Following an analysis of a road accident black-spot, it has been decided to reinforce the crash barrier shown with an additional post. The post is to be centered between the posts X and Y shown opposite. Tensile test results on three metals A, B and C, which may be suitable for the additional post, are shown. Analyse the main properties of metals A, B and C. [Image: A crash barrier with two posts labelled X and Y. A graph shows Stress vs Strain for three metals A, B, and C, with C being the stiffest and strongest, B intermediate, and A the weakest and most ductile.]