Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (12)
2017 · Part B · Q6(c) · 14 marks · p.8
A NAND gate is a combination of an AND gate and a NOT gate. Copy and complete the truth table below for the combination of gates shown. [Diagram: A logic circuit diagram consisting of three input gates (X, Y, Z) feeding into a NAND gate, which then feeds into an inverter (NOT gate), producing an output W.] [Table: An empty truth table with columns for INPUT (X, Y, Z) and OUTPUT (W).]
Marking scheme
[Completed truth table for the combination of gates: Row 1: 1, 1, 1, 1. Row 2: 1, 0, 1, 0. Row 3: 0, 1, 1, 0. Row 4: 0, 0, 0, 0.]
2017 · Part B · Q6(b) · 12 marks · p.8
For the system shown, copy and complete the truth table for the following situation: (indicate if each of the positions marked are at '1' or '0') ‘The ignition switch is on, the driver seat is occupied but the seat belt is open, while the passenger seat is vacant but the seat belt is closed.' [Diagram: A system diagram for a two-seat car seat belt monitoring system. It includes ignition input, seat sensors (SS1, SS2), seat belt sensors (SB1, SB2), logic gates (A, B, C, D, E, F, G, H, I, J), a visual warning display, and an audible warning. The diagram shows inputs and outputs for each component.] [Table: An empty truth table with columns labelled E, F, G, H, I, J.]
Marking scheme
[Completed truth table: E=1, F=1, G=1, H=1, I=0, J=0.]
2015 · Part B · Q2(a) · 25 marks · p.4
2 (a) In order to help conserve water use in a shower, the 555 timer circuit shown will be used to indicate that 4 minutes have passed. The timing circuit, when started by pushing the PTM switch, will turn on the green LED for 4 minutes and after that time will turn on the red LED. [Circuit Diagram: A 555 timer circuit with components R1, R2, C1, C2, On/Off switch, PTM switch, Red LED, Green LED, and a 555 chip with labelled pins. Also shown is a diagram of a 555 chip with a notch and a chip socket.] (i) Explain the purpose of the notch on the 555 chip. (ii) Explain why the use of a chip socket is recommended when soldering this circuit. (iii) State two advantages of using a printed circuit board over copper stripboard to make this circuit. (iv) Explain the difference between the On/Off and PTM switches. (v) How could the 4 minute time delay be increased? (vi) What change could be made to the circuit to produce a sound after the 4 minutes have passed? (25 marks)
2015 · Part B · Q4(b)(ii) · p.7
(ii) Explain, giving two reasons, why robotic manufacturing is more commonly used in first world countries. (20 marks)
Marking scheme
[10 marks: 2 x 5marks (5, 3, 2, 1)] Cost of labour low, required infrastructure not available, expertise to set up and operate plant not readily available, etc. [Diagram: Comparison of a highly automated factory in a developed country versus a less automated factory in a developing country, highlighting cost and infrastructure differences.]
2015 · Part B · Q4(b)(i) · p.7
(b) Robotic devices are commonly used on factory production lines. (i) Outline two advantages of using robots in this situation. (20 marks)
Marking scheme
[10 marks: 2 x 5 marks (5, 3, 2, 1)] Accuracy, no errors, longer production times, etc. [Diagram: Robotic arm performing a precise task on a factory production line, illustrating accuracy and efficiency.]
2015 · Part B · Q4(a)(iii) · p.7
(iii) In both cases, outline why control systems are required for their operation. (30 marks)
Marking scheme
[ 10 marks: 2 x 5 marks (5, 3, 2, 1)] Control system required to alter direction of movement or speed of drone/car to maintain safe path/avoid collision, concept of data received by sensors used to control operation of device, etc. [Diagram: Flowchart showing how sensors provide input to a control system, which then outputs commands to the vehicle's actuators (steering, throttle).]
2015 · Part B · Q4(a)(ii) · p.7
(ii) Outline one advantage and one disadvantage in developing these technologies. (30 marks)
Marking scheme
[10 marks: 2 x 5 marks (5, 3, 2, 1)] One advantage drone -survey inaccessible areas, search and rescue, etc. or One advantage car -safety, driver error eliminated, ‘drivers' not tired, etc. One disadvantage drone -privacy, safety, regulation, etc. or One disadvantage car -high cost, driving ‘experience' removed, etc. [Diagrams: Contrasting images of drones and driverless cars, highlighting advantages (e.g., rescue scene, safe driving) and disadvantages (e.g., surveillance, high cost).]
2015 · Part B · Q4(a)(i) · p.7
4. Control Systems & Technology and Society (a) In the case of each of the following: driverless cars and unmanned aerial vehicles (drones). [Image: A driverless car and a drone.] (i) Outline how 'input sensors' are used in their operation. (30 marks)
Marking scheme
[ 10 marks: 2 x 5 marks (5, 3, 2, 1)] Input sensor -GPS, proximity sensors, altimeter, tilt sensor, speed sensor, etc. Outline how each sensor used in each example. [Diagrams: Driverless car and drone, with labels pointing to sensors like GPS, lidar, cameras, radar, altimeter, etc., and explanations of their function.]
2015 · Part B · Q6(b)(ii) · 20 marks · p.8
(ii) [Logic Diagram: Two inputs U and V feeding into two NAND gates, the output of which feeds into a third NAND gate, producing output W.] (20 marks)
Marking scheme
INPUT OUTPUT U V X Y W 1 1 0 0 1 1 0 0 1 1 0 1 1 0 1 0 0 0 1 1 0 [Completed truth table for the second NAND gate combination, identifying it as an OR gate.]
2015 · Part B · Q6(b)(i) · p.8
(b) A NAND gate is a combination of an AND gate and a NOT gate. NAND gates can be combined to form other logic gates. Using a truth table in each case, identify the gates produced by the NAND gate combinations shown. (i) [Logic Diagram: Two inputs R and S feeding into two NAND gates, the output of which feeds into a third NAND gate, producing output T.] (20 marks)
Marking scheme
INPUT OUTPUT R S X T 1 1 0 1 1 0 1 0 0 1 1 0 0 0 1 0 [Completed truth table for the first NAND gate combination, identifying it as an AND gate.]
2015 · Part B · Q6(a)(ii) · 10 marks · p.8
(ii) The system diagram below is used to activate a flashing orange light if a fault develops in the traffic light system at (a) above. [System Diagram: A fault input (Fault=0) feeding into a logic gate arrangement (X) which produces a 'Flashing Orange light' output.] Name the special arrangement of gate shown at X and explain why the PTB switch is used with this arrangement. (10 marks)
Marking scheme
X: Latch (5 marks), Explain PTB (5 marks (5,3,1)) Output from OR gate is a ‘l' if a fault to detected. Output loops back to input of OR gate, keeping output at ‘l' even if fault =1. Pushing PTB (push to break) switch will send a '0' to input of OR gate and stop the orange light flashing. [Diagram: Logic circuit showing a latching mechanism using an OR gate and a PTB (push-to-break) switch, controlling a flashing orange light.]
2015 · Part B · Q6(a)(i) · 20 marks · p.8
6. Control Systems (a) A system diagram to control a set of traffic lights is shown. A coloured light will switch on if a '1' output is received from the system and will switch off if a '0' output is received. [System Diagram: Inputs X and Y feeding into logic gates (NOT, AND, OR) which produce outputs for Red, Orange, and Green lights. Also shown is a traffic light.] (i) Copy the truth table below into your answerbook. Complete the table to indicate which lights will be switched on/off for each input shown. [Table: Inputs X and Y, Outputs Red, Orange, Green. Rows: (1,1), (1,0), (0,1), (0,0).] (20 marks)
Marking scheme
X Y Red Orange Green 1 1 off on off 2,2,1 1 0 off off on 2,2,1 0 1 on on off 2,2,1 0 0 on off off 2,2,1 [Completed truth table for traffic lights: Input X, Y and corresponding Red, Orange, Green light outputs shown as 'on' or 'off'.]