Study notes
No notes have been generated for this topic yet. Open the topic page online and click Generate notes first.
Past exam questions (12)
2015 · Part B · Q6(b)(ii) · 20 marks · p.8
Using a truth table in each case, identify the gates produced by the NAND gate combinations shown. [Diagram: Logic circuit with inputs U, V and output W, composed of NAND gates.]
2015 · Part B · Q6(b)(i) · p.8
Using a truth table in each case, identify the gates produced by the NAND gate combinations shown. [Diagram: Logic circuit with inputs R, S and output T, composed of NAND gates.]
2015 · Part B · Q6(a)(ii) · 10 marks · p.8
The system diagram below is used to activate a flashing orange light if a fault develops in the traffic light system at (a) above. [Diagram: A logic gate circuit with input 'Fault = 0' and output 'Flashing Orange light', labelled X at the gate arrangement.] Name the special arrangement of gate shown at X and explain why the PTB switch is used with this arrangement.
2015 · Part B · Q6(a)(i) · 20 marks · p.8
Copy the truth table below into your answerbook. Complete the table to indicate which lights will be switched on/off for each input shown. [Diagram: A system diagram for traffic lights with inputs X and Y and outputs Red, Orange, Green lights. Table: Input X, Input Y, Red, Orange, Green columns.]
2014 · Part B · Q2(b) · p.5
The sketch shows a mechanism to lock and unlock a door. [Diagram: A mechanism for locking a door. It includes a motor (150 RPM), a gear system with a 20-tooth gear meshing with a 5-tooth gear (5 teeth = 10 mm), a bolt, and a lock mechanism. Arrows indicate the direction of motion.] (i) Name the mechanism shown at X. State one advantage of using this mechanism in a lock. (ii) The mechanism at X changes the direction of motion through 90°. Name and sketch another mechanism which also achieves this change. (iii) Using the information given in the sketch, calculate the length of time for which the motor must run to move the bolt a distance of 30 mm. (iv) The door can be locked and unlocked, using a circuit constructed from the following components: a battery, a DPDT switch and a motor. Indicate how these components should be connected to allow the door to lock and unlock. (v) Explain why limit switches should be used as part of the controlling circuit.
2014 · Part B · Q2(a) · 25 marks · p.4
The diagram shows the component layout for a flashing LED circuit. (LED1 on, LED2 off, LED1 off, LED2 on) [Circuit diagram: A flashing LED circuit with two transistors (T1, T2), four resistors (R1, R2, R3, R4), two capacitors (C1, C2), and two LEDs (LED1, LED2). Power supply is +9V and 0V.] (i) LED1 has the following values: Vf = 2V and Imax = 0.02A. Calculate the required value of R1 in the circuit shown. (ii) The required value of resistor R2 is 47kΩ. Use the resistor colour codes shown below to determine the colour bands of this resistor. [Table: Resistor Colour Codes. Black=0, Brown=1, Red=2, Orange=3, Yellow=4, Green=5, Blue=6, Violet=7, Grey=8, White=9.] (iii) Identify the components shown at C1 and C2. What unit is used to measure the value of C1 and C2? What effect will increasing the value of these components have on the operation of the circuit? (iv) Copy the symbol for transistor T1 into your answerbook and indicate clearly the position of the base and the emitter.
2014 · Part B · Q4(b) · 10 marks · p.7
Robotic devices are commonly used in military operations and in space exploration. In each case, explain the advantages of using robotic devices for these operations.
2014 · Part B · Q4(a) · 40 marks · p.7
The graphics show a base platform for an educational robot. [Diagram: A base platform for a robot, showing a castor wheel at the bottom, two drive motors with gearboxes at the top, and a perspective view of the robot with wheels and motors.] (i) Outline two reasons why the castor is required. (ii) Explain why gear boxes are attached to the drive motors. (iii) Outline two reasons why some robots use tracks instead of wheels. (iv) Explain how, using the two motors, the robot can move forward in a straight line and then turn left. (v) Outline how such a robot could detect and avoid an obstacle (e.g. a wall).
2014 · Part B · Q6(iv) · 10 marks · p.8
A latched alarm is required to indicate that there is no oil in the tank. Explain how a latch alarm can be constructed from an ‘OR' logic gate.
2014 · Part B · Q6(iii) · 10 marks · p.8
Copy the truth table below into your answerbook. For each of the situations described below, use the truth table to identify the logic states (1 / 0) at the points marked X, Y, Z, W, R, S, T, U and V. [Table: A truth table with columns X, Y, Z, W, R, S, T, U, V and two rows labelled Situation 1 and Situation 2.] Situation 1: The system is turned on, there is sufficient oil in the tank, a low temperature is detected by S3 and a low temperature is detected by S4. Situation 2: The system is turned on, there is no oil in the tank, a high temperature is detected by S3 and a low temperature is detected by S4.
2014 · Part B · Q6(ii) · 10 marks · p.8
Draw truth tables for gates C and E.
2014 · Part B · Q6(i) · 10 marks · p.8
Name the logic gates required at A, C, D and E.